Buick Park Avenue, Lesabre Front Wheel Hub Bearing Replacement – Auto Repair Instructions. Here is a great set of instructions for the installation of a GM front wheel hub bearing assembly. One of our customers submitted this for us to show to the public. Hopefully anyone thinking about tackling this job will find these helpful. These instructions came from a 2.

Save $1,919 on a used Buick Park Avenue. Search pre-owned Buick Park Avenue listings to find the best local deals. CarGurus analyzes over 6 million cars daily.

Buick Lesabre Limited, however they will work for numerous GM front wheel drive vehicles including: Buick Lesabre, Park Avenue, Centruy, Regal, Riviera, Rendezvous. Cadillac Concours, Seville, Deville, Eldorado. Chevrolet Impala, Monte Carlo, Venture. Oldsmobile Aurora, Intrigue, Silhouette. Pontiac Aztec, Bonneville, Grand Prix, Montanna, Transport. Removal. 1. Remove hub cap/dust cover. Tip: If you do not have an impact wrench (air operated gun), you may want to remove the center axle nut at this point.

Removing this nut with the wheel still on and before jacking up the vehicle, will make it much easier and give you enough leverage to get it loose with a regular ratchet or breaker bar (recommended). You may have access to the axle nut without removing the wheel. If you do not have access, you can remove the wheel and put the spare tire/wheel on. The spare wheel has a very large center hole and gives you access to the center axle nut.

Quality used auto parts instantly. This Service uses Car-Part Interchange By clicking on "SEARCH" you agree to Terms. Learn More About Your Vehicle Maintenance Features And The Buick Protection Plan. Download Your Owner’s Manual For More Vehicle Maintenance Information. Get Buick Regal expert reviews, new and used Regal prices and ratings. View Buick Regal specs, pictures, and get buying advice at The Car Connection. Subscribe and SAVE, give a gift subscription or get help with an existing subscription by clicking the links below each cover image. Auto Parts and Truck Part for Car and Automotive parts. Depending on your sense of history, you might remember when Volvos were deemed “boxy but nice.” Maybe even farther back you recall the sleek P1800. But no matter. We take pride in offering the most extensive collection of Buick parts online. Buy here and take advantage of our low prices.

With the vehicle back on the ground, you can put the breaker bar with the proper size axle nut socket, on the nut and loosen it. Then jack up the vehicle and remove the wheel.

Quality Remanufactured Buick Engines From Remanufactured.com for: Century, Electra, Jeep, Jeepster, LeSabre, Park Ave, Regatta, Regal, Riviera, Skyhawk, Skylark. Workhorse, automotive repair manual, service manuals, owners manaul, user guide, sale brochure, parts book.

Jack up vehicle and support properly. You should always put a jack stand under the vehicle and use that to supprt the vehicle, not the jack. Also you should also use wheel ckocks to prevent the vehicle from accidentally rolling. If you are doing do- it- yourself repairs often, it is wise to buy good quality tools and equipment.

This can help get the job done quicker and certainly safer. Remove lug nuts using 1.

Remove wheel and set aside. Remove 2 caliper mounting bolts using a 1. Set caliper aside. Do not let it hang from rubber brake hose. Remove 2 caliper mount bolts using 1. Set caliper mount aside. Remove brake rotor by sliding it off and set aside.

NOTE: If the brake rotor has never been removed, their may be 2 small screws or retainers holding it in place. Sony Vegas Pro Cracked Download. Remove these and the rotor will slide off. If it is stuck, you can lightly tap it with a hammer.

Remove 3 hub mounting bolts using 1. These are located on the inside of the steering knuckle next to the outer CV boot. A 3/8’s drive ratchet with swivel and extension is best for this. Also if you are having trouble, look closely at how you have it jacked up. You may be able to reposition the jack and change the angle of the axle.

If you have it jacked up under the control arm, you still have the suspension compressed. If you jacked it up by the frame rail, the suspension is opened up and may give you a better angle. Again be very careful with the jack and always use a jack stand for support. You can always use more then one jack stand to help as a safety also. Remove axle nut using 1 5/1. Unhook and then unplug the ABS sensor.

Remove hub assembly. Be careful to make sure the axle splines are free from the hub. Once you have the axle nut off you should be able to push the axle in towards the engine with the bottom of the palm of your hand. If it is stuck, you can rethread the axle nut 1- 2 threads, then place the socket back on and tap it with a hammer. This is mainly to assure the axle does nte get pulled out while pulling off the hub. The hub may also require a slight tap with a hammer or very rarely a puller to get the hub loose.

Hit the hub and pry with a screwdriver or small prybar until hub comes out. Clean mounting area with a wire brush so new hub slides on easily.

Make sure their is no rust or material that may cause the hub to not sit flush. Install new hub assembly. Use thread locker on the 3, 1. This is because the torque can be affected by re- using the bolts.

The threads stretch when the are originally installed/removed and they can never really be torqued properly again. Also it is strongly recommended to replace the axle nut for the same reason**1.

Hook up the new sensor plug. Install the axle nut using a 1 5/1. VERY IMPORTANT!!!

Do not over torque or under torque this nut. Also it is strongly recommended to never use an impact wrench to tighten this nut. Please tighten with a torque wrench to 1. Lbs.(Other year and model vehicle torques specs may differ, please email us if you would like to know yours. Over or under torqueing this nut is the number one cause of premature bearing failure!!!!!!( It is also recommended to replace this nut as the threads will usually be stretched from being installed and removed. Threads will be stretched if installed with an impact wrench and also the bearing will be squeezed excessively which will cause premature failure. Bmw Software Update Usb Format Tool. Slide on the brake rotor.

Use a tiny bit of thread locker on the 2, 1. Install the caliper mount bolts using a 1. Install the wheel using a 1. Torque lug nuts with torque wrench to 1.

Ft. Lbs.) and press hub dust cover into place. View this item on our website. View Impala & GM Window Motor & Regulator Assemblies Here. View GM Headlights Here.

View GM Radiator Fans Here. View GM Brake Calipers Here. View GM Wiper Motors Here. View GM Side View Mirrors Here.